SINGLE SUSPENSION FREE CENTRE TYPE -PIPE ARCING HORN LINE SIDE WITH ARMOUR ROD

Home » Suspension » Free Center Type » SINGLE SUSPENSION FREE CENTRE TYPE -PIPE ARCING HORN LINE SIDE WITH ARMOUR ROD

SINGLE SUSPENSION FREE CENTRE TYPE -PIPE ARCING HORN LINE SIDE WITH ARMOUR ROD

MMPT have created an identifiable position in the market by manufacturing and supplying superior quality Suspension Hardware.
The main purpose of this hardware is to hang the conductor/cable to the insulator. The clamps help to link all other fittings and accessories to the tower arms. It promotes safety of the conductor/cable and people by preventing voltage leakage. It enchance the stability of the conductor by limiting their movement, especially against a strong wind, storms and other natural calamities.

Free centre suspension clamp are the clamps in which bolt/locking arrangements are in the bottom part of the clamp.

Armor rods are designed to protect cables from bending, compression, abrasion and flash-over. it can also be used in repairing damaged aluminium-based conductors and restore the mechanical strength of the conductor and conductivity of the conductor.The raw materials of the armor rod are aluminium wire, galvanized steel wire, and aluminium clad steel wire.The armour rod material should be similar to the conductor surface material, avoiding corrosion between different elements.

Arcing horns (Pipe Type)are projecting conductors used to protect insulators or switch hardware on high voltage electric power transmission systems from damage during lightning strikes and other overvoltage phenomena.
Arcing horns provide a path for flashover to occur that bypasses the surface of the protected device. Horns are normally paired on either side of an insulator, one connected to the high voltage part and the other to ground, or at the breaking point of a switch contact.

MMPT suspension hardware can be custom manufactured with different wire numbers, a wide range of cable sizes, wire raw material.

BOQ

SL. NO DESCRIPTION MATERIAL QTY./SET
1
BALL HOOK
F.S., HDG
1 NOS
2
SOCKET EYE HORN HOLDER
F.S., HDG
1 NOS
3
ARCING HORN PIPE TYPE-TWO HOLE
M.S. , HDG
1 NOS
4
SUSPENSION CLAMP CENTRE FREE TYPE
AL. ALLOY
1 NOS
5
M16 HEX BOLT, NUT, ROUND & SP. WASHER
M.S. , HDG
1 SET
6
M12 HEX BOLT, NUT, ROUND & SP. WASHER
M.S. , HDG
2 SETS
7
SPLIT PIN
S.S.
1 NOS
8
R-CLIP
S.S.
1 NOS
9
ARMOUR ROD
AL. ALLOY, 6061 T6
1 SET

TECHNICAL DATA

  1. ALL DIMENSIONS ARE IN MM.
  2. GENERAL TOLERANCE ±3%
  3. U.T.S. OF HARDWARE FITTING : 90 KN.
  4. U.T.S. OF SUSPENSION CLAMP – 70 KN.
  5. SLIP STRENGTH OF SUSPENSION CLAMP : 8% TO 15% UTS OF CONDUCTOR.
  6. BALL & SOCKET DESIGNATION : 16MM & 16MM ”B” AS PER IS : 2486, PART-II.
  7. SPECIFICATION TO WHICH H/W FITTING CONFORM – IS : 2486, PART-I.
  8. ALL FERROUS PARTS (EXCEPT SPRING WASHER) SHALL BE HOT DIP GALVANISED CONFORMING TO IS : 2633 AND SPRING WASHER ELECTRO GALVANISED CONFORMING TO IS : 1573, SERVICE COND. III.
  9. TOLERANCE IN TOTAL LENGTH OF HARDWARE FITTING  ±2%.
  10. MAGNETIC POWER LOSS AT 500A PER SUSPENSION CLAMP – 1Watt (MAX.)

AVAILABLE FOR THE FOLLOWING CONDUCTORS

For ACSR

SL. NO ACSR CODE CONDUCTOR DIA.
1
RACCOON
12.27
2
DOG
14.15
3
LEOPARD
15.84
4
COYOTE
15.86
5
TIGER
16.52
6
WOLF
18.13
7
ORIOLE
18.82
8
LYNX
19.53
9
LARK
20.47
10
PANTHER
21.00
11
LION
22.26
12
BEAR
23.45
13
GROSBEAK
25.16
14
TEAL
25.24
15
GOAT
25.97
16
ANTELOPE
26.73
17
KUNDAH
26.80
18
SHEEP
27.93
19
DRAKE
28.14
20
ZEBRA
28.62
21
DEER
29.89
22
CAMEL
30.15
23
ELK
31.50
24
MORKULLA
31.68
25
MOOSE
31.77
26
BERSIMIS
35.05

For AAAC

SL. NO AAAC CODE CONDUCTOR DIA.
1
RABBIT
9.30
2
DOG
12.78
3
PANTHER
19.70
4
PANTHER-UP
22.05
5
YEW
25.97
6
ZEBRA
28.00
7
ZEBRA-UP
29.79